TubeSoundAUv3 SetupLogic Pro

Mac and iPad · Updated 10 November 2026

Tube saturation on a Logic Pro drum bus

Use one TubeSound instance on a drum track or bus. This example compares the same drum loop with the effect bypassed, then with the Low and High settings below. Listen to the kick and snare before deciding how much drive to keep.

ListenSetupTry the settingsTroubleshooting

Drum loop · 110 BPM

Hear the difference

Follow the kick and snare. Low adds bite to the loop. High uses a lower plate voltage and more drive to push the circuit much harder. Compare the body and tail of each hit.

Selected: Dry. Press Play to listen.

Mode
Pro
Starting preset
British Chime
Tube
12AX7

High also changes Plate V, Grid Bias and Interstage. The exact settings are listed below.

Original synthesized audio, rendered offline with TubeSound's DSP. Playback loudness is matched. High is deliberately driven harder to make the change easier to hear.

Dry MP3 · Low MP3 · High MP3. Use the WAV to try these settings in your host.

Insert TubeSound in Logic Pro

Install TubeSound from the App Store and open it once. You can start on one audio track. A bus makes sense when several drum tracks should pass through the same instance.

On Mac

  1. Open the Mixer and select the track or aux channel you want to process.
  2. Click an empty Audio FX slot.
  3. Choose Audio Units, find TubeSound under its manufacturer entry, and select the version that matches the channel format.
  4. Play the project and open the plug-in window.

On iPad

  1. Select the track and open its Plug-ins area.
  2. Tap Add Audio FX.
  3. Open Audio Units and choose TubeSound.
  4. Double-tap the plug-in name to open its detailed controls.

TubeSound belongs in Audio FX. Keep the drum instrument in its instrument slot.

Compare the drum settings

  1. Import the source WAV into an audio track and loop the pattern.
  2. Insert TubeSound, choose Pro mode and load British Chime.
  3. For Low, set Input to 0.85. Leave the remaining circuit controls at the preset values.
  4. Use Output to match the level to bypass.
  5. For High, set Input to 2.00, Plate V to 150 V, Grid Bias to −0.50 V and Interstage to 0.80. Match Output again before comparing.

High changes the circuit settings as well as Input. It is a deliberately pushed example, so start lower when using TubeSound on a full drum mix. The source WAV retains the level sent into the effect.

Move from one loop to a drum bus

When using separate kick, snare and overhead tracks, route their outputs to one bus. Insert TubeSound on the receiving aux channel. Keep that aux routed to your normal output.

Check the level arriving at the bus before copying the example's Input value. Several tracks together may drive the circuit harder than the single downloadable loop.

If the kick loses definition, lower Input and compare again. If the cymbals become too prominent, reduce Input before trying a different preset. Keep a compressor before or after TubeSound only when you need what it does, then compare both orders.

Check routing before changing the preset

If the plug-in opens but has no effect, check that it is on the channel carrying the drums. If a bus sounds unexpectedly loud, make sure the same drums are not reaching the output through a second parallel route.

On Mac, turn off TubeSound's separate system-wide processing while comparing the plug-in. That keeps the listening path from processing the same audio twice. If TubeSound is absent from Logic's menu, open its app once, restart Logic and check Logic's Plug-in Manager.

Host documentation

Other host guides

For the circuit controls, see the TubeSound Pro Guide.

Try it on your own track

TubeSound is free to try. The trial has periodic silent breaks. A one-time in-app purchase removes them. Use Restore Purchases if you have already bought the app.

Try TubeSound on the App Store